Comtech EF Data KPA-040 Manual de instalación Pagina 75
- Pagina / 183
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MNC-0400-001 17 of 54 REV H
Operation, Rack and Digital HPAs
Power Out—The current RF output power of the amplifier. The
RF output is continuously monitored and displayed on this
menu.
Atten Set—The current attenuator setting. This is only available
when High Voltage is OFF.
RFLTD PWR—The current value of reflected power present at
the output of the amplifier. Reflected power is continuously
monitored and displayed on this menu. This is only available
when High Voltage is ON.
Ew—Current Helix Voltage.
Iw—Current Helix Current.
Ef—Current Heater Voltage.
Temp—Current TWT collector temperature in either Fahrenheit
or Centigrade.
Note
The default values for the units displayed on the Status 2 Menu is set
via the Setup Menus which are discussed later in this chapter.
Three of the softkeys of the Displayall Menu are active. The
functions of these three softkeys are:
[Softkey 1]—Temporarily changes the units used for both the RF
Output and RF Reflected Power displays. Cycles one step each
time [Softkey1] is pressed. The sequence of the steps is:
Watts dBm dBw Watts, etc.
[Softkey 2]—Same as [Softkey 1].
[Softkey 4]—Temporarily changes the temperature units used
for the temperature data display. Toggles between degrees
F (Fahrenheit) and degrees C (Centigrade.)
The [Enter] key is pressed to go back to the Status 2 Menu from
the Displayall Menu.
The third line of the Displayall Menu shows the Helix Voltage
(Ew) in kilovolts (DC) and the Helix Current (Iw) in milliamperes.
The fourth line of the display shows the Heater Voltage (Ef) and
the TWT collector temperature (Temp) in Fahrenheit or
Centigrade.
EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject
to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person,
whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
- XTRD-400K 1
- Operation and 1
- Installation Manual 1
- MN5-0062-301 ii Revision A 4
- About this manual 5
- Who should use this manual 6
- References 11
- Abbreviations and Acronyms 11
- CE Symbols 17
- MNC-0100-001 2 Revision B 20
- MNC-0100-001 4 Revision B 22
- Physical Characteristics 23
- Environmental Characteristics 23
- Specifications 23
- Contacting Xicom Technology 24
- Safety/Sicherheit 25
- General Warnings and Cautions 29
- Sicherheit 32
- Unpacking and Installation 39
- Auxiliary Interface Connector 47
- Grounding 58
- ParagraphTitle Page Number 60
- Number Title Page Number 62
- MNC-0400-001 6 of 54 REV H 64
- Controls and Indicators 65
- MNC-0400-001 8 of 54 REV H 66
- MNC-0400-001 9 of 54 REV H 67
- MNC-0400-001 10 of 54 REV H 68
- MNC-0400-001 11 of 54 REV H 69
- Menu and Screen Descriptions 71
- MNC-0400-001 14 of 54 REV H 72
- MNC-0400-001 15 of 54 REV H 73
- MNC-0400-001 16 of 54 REV H 74
- MNC-0400-001 17 of 54 REV H 75
- MNC-0400-001 18 of 54 REV H 76
- MNC-0400-001 19 of 54 REV H 77
- MNC-0400-001 20 of 54 REV H 78
- MNC-0400-001 21 of 54 REV H 79
- MNC-0400-001 22 of 54 REV H 80
- MNC-0400-001 23 of 54 REV H 81
- MNC-0400-001 24 of 54 REV H 82
- MNC-0400-001 25 of 54 REV H 83
- MNC-0400-001 26 of 54 REV H 84
- MNC-0400-001 27 of 54 REV H 85
- MNC-0400-001 28 of 54 REV H 86
- MNC-0400-001 29 of 54 REV H 87
- Figure 11, Setup Menu 2 88
- MNC-0400-001 31 of 54 REV H 89
- • Select band 90
- MNC-0400-001 33 of 54 REV H 91
- MNC-0400-001 34 of 54 REV H 92
- MNC-0400-001 35 of 54 REV H 93
- MNC-0400-001 36 of 54 REV H 94
- MNC-0400-001 37 of 54 REV H 95
- MNC-0400-001 39 of 54 REV H 97
- Menutrees 98
- MNC-0400-001 41 of 54 REV H 99
- MNC-0400-001 42 of 54 REV H 100
- MNC-0400-001 43 of 54 REV H 101
- MNC-0400-001 44 of 54 REV H 102
- Initial Setup and Operation 103
- MNC-0400-001 46 of 54 REV H 104
- • Standby 105
- • Heater Standby 105
- • Beam ON 105
- • Filament Time Delay 105
- MNC-0400-001 48 of 54 REV H 106
- MNC-0400-001 49 of 54 REV H 107
- MNC-0400-001 50 of 54 REV H 108
- MNC-0400-001 51 of 54 REV H 109
- MNC-0400-001 52 of 54 REV H 110
- MNC-0400-001 53 of 54 REV H 111
- MNC-0400-001 54 of 54 REV H 112
- Record of Changes 113
- Table of Contents 114
- Paragraph Title Page Number 114
- List of Figures 115
- List of Tables 116
- Overview 117
- Communication 117
- Compatibility 117
- Figure 1, Basic Configuration 118
- Protocol 119
- Commands and Queries 127
- XX.X in dBm 135
- Preventive Maintenance 149
- Maintenance Procedures 152
- Wartungsverfahren 154
- Service and Repair 157
- MNC-0700-001 4 Revision F 160
- Service and Repair 160
- RMA REQUEST FORM 161
- MNC-0700-001 6 Revision F 162
- TWTA SPECIFICATION 163
- XTRD-400K, 400W, SNG 163
- Appendix A 171
- 173
- 173
- 175
- 175
- 175
- 176
Relacionado con productos y manuales para Amplificadores de audio Comtech EF Data KPA-040
(6 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales