Comtech EF Data KPA-040 Manual de instalación Pagina 105
- Pagina / 183
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
MNC-0400-001 47 of 54 REV H
Operation, Rack and Digital HPAs
Note
Refer to the chapter titled Overview for general amplifier specifications
and the appendix Specifications for specifications that are specific to
your particular amplifier.
Operating Configurations
There are two operating configurations: LOCAL and REMOTE.
In LOCAL, all operations are controlled from the TWTA Front
Panel. The controls and indicators were shown and summarized
at the beginning of this chapter. In REMOTE the front panel high
voltage and setup functions are inhibited.
Note
Familiarity with the XTRD menu system is required for LOCAL
operation. Familiarity with the XICOM command set is required for
REMOTE operation.
Operating Modes
The operating modes of the TWTA are described in the
following sections. There are four amplifier operating modes:
• Filament Time Delay
• Standby
• Heater Standby
• Beam ON
• Fault
Filament Time Delay Mode (FTD)
When power is first applied to the amplifier, voltage is applied to
the TWT's filament. The TWT's filament must be at its operating
temperature for the tube to function properly. The typical warm-
up period is three minutes. During this warm-up period, the FTD
indicator (amber) will be illuminated. When the delay cycle is
complete, the FTD indicator will be dark.
If there is a power failure, high voltage will be OFF for a period
proportional to prime power off-time. At the end of the recovery
period, if high voltage is ON when the prime power interruption
occurs, high voltage is automatically restored
EAR EXPORT CONTROLLED: The information contained in this Manual refers or relates to a product that is subject
to the U.S. Export Administration Regulations (EAR). Transfer of data herein by any means to a Foreign Person,
whether in the U.S. or abroad, may require an export license from the U.S. Department of Commerce.
- XTRD-400K 1
- Operation and 1
- Installation Manual 1
- MN5-0062-301 ii Revision A 4
- About this manual 5
- Who should use this manual 6
- References 11
- Abbreviations and Acronyms 11
- CE Symbols 17
- MNC-0100-001 2 Revision B 20
- MNC-0100-001 4 Revision B 22
- Physical Characteristics 23
- Environmental Characteristics 23
- Specifications 23
- Contacting Xicom Technology 24
- Safety/Sicherheit 25
- General Warnings and Cautions 29
- Sicherheit 32
- Unpacking and Installation 39
- Auxiliary Interface Connector 47
- Grounding 58
- ParagraphTitle Page Number 60
- Number Title Page Number 62
- MNC-0400-001 6 of 54 REV H 64
- Controls and Indicators 65
- MNC-0400-001 8 of 54 REV H 66
- MNC-0400-001 9 of 54 REV H 67
- MNC-0400-001 10 of 54 REV H 68
- MNC-0400-001 11 of 54 REV H 69
- Menu and Screen Descriptions 71
- MNC-0400-001 14 of 54 REV H 72
- MNC-0400-001 15 of 54 REV H 73
- MNC-0400-001 16 of 54 REV H 74
- MNC-0400-001 17 of 54 REV H 75
- MNC-0400-001 18 of 54 REV H 76
- MNC-0400-001 19 of 54 REV H 77
- MNC-0400-001 20 of 54 REV H 78
- MNC-0400-001 21 of 54 REV H 79
- MNC-0400-001 22 of 54 REV H 80
- MNC-0400-001 23 of 54 REV H 81
- MNC-0400-001 24 of 54 REV H 82
- MNC-0400-001 25 of 54 REV H 83
- MNC-0400-001 26 of 54 REV H 84
- MNC-0400-001 27 of 54 REV H 85
- MNC-0400-001 28 of 54 REV H 86
- MNC-0400-001 29 of 54 REV H 87
- Figure 11, Setup Menu 2 88
- MNC-0400-001 31 of 54 REV H 89
- • Select band 90
- MNC-0400-001 33 of 54 REV H 91
- MNC-0400-001 34 of 54 REV H 92
- MNC-0400-001 35 of 54 REV H 93
- MNC-0400-001 36 of 54 REV H 94
- MNC-0400-001 37 of 54 REV H 95
- MNC-0400-001 39 of 54 REV H 97
- Menutrees 98
- MNC-0400-001 41 of 54 REV H 99
- MNC-0400-001 42 of 54 REV H 100
- MNC-0400-001 43 of 54 REV H 101
- MNC-0400-001 44 of 54 REV H 102
- Initial Setup and Operation 103
- MNC-0400-001 46 of 54 REV H 104
- • Standby 105
- • Heater Standby 105
- • Beam ON 105
- • Filament Time Delay 105
- MNC-0400-001 48 of 54 REV H 106
- MNC-0400-001 49 of 54 REV H 107
- MNC-0400-001 50 of 54 REV H 108
- MNC-0400-001 51 of 54 REV H 109
- MNC-0400-001 52 of 54 REV H 110
- MNC-0400-001 53 of 54 REV H 111
- MNC-0400-001 54 of 54 REV H 112
- Record of Changes 113
- Table of Contents 114
- Paragraph Title Page Number 114
- List of Figures 115
- List of Tables 116
- Overview 117
- Communication 117
- Compatibility 117
- Figure 1, Basic Configuration 118
- Protocol 119
- Commands and Queries 127
- XX.X in dBm 135
- Preventive Maintenance 149
- Maintenance Procedures 152
- Wartungsverfahren 154
- Service and Repair 157
- MNC-0700-001 4 Revision F 160
- Service and Repair 160
- RMA REQUEST FORM 161
- MNC-0700-001 6 Revision F 162
- TWTA SPECIFICATION 163
- XTRD-400K, 400W, SNG 163
- Appendix A 171
- 173
- 173
- 175
- 175
- 175
- 176
Relacionado con productos y manuales para Amplificadores de audio Comtech EF Data KPA-040
(6 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.096 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales