Comtech EF Data LPOD Especificaciones Pagina 124
- Pagina / 218
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
LPOD C-, X-, or Ku-Band Outdoor Amplifier / Block Up Converter (BUC) MN-LPOD
Serial-based Remote Product Management Revision 10
5–24
Parameter Type
Command
(Instruction
Code and
Qualifier)
Arguments
for Command
or Response
to Query
Description of Arguments
(Note that all arguments are printable ASCII characters)
Response to
Command
(Target to
Controller)
Query
(Instruction
Code and
Qualifier)
Response to Query
(Target to
Controller)
Unit Alarm Mask
MSK=
5 bytes
Command or Query.
Sets or returns alarm mask conditions in the form abcde, where:
0 = Fault, 1 = Alarm, 2 = Masked
a = Low Forward RF Power
b = External Reference Lock detect
c = Fan Speed
d = LNB Current Detect
e = LNB 22V Power Supply
Default value: 22111
Example: <1/MSK=22111’cr’
>0001/MSK=1’cr’’lf’
MSK=
MSK?
MSK*
MSK?
MSK=abcde
(See Description of
Arguments)
Mute State
MUT=
1 byte
Command or Query.
Sets or return the unit mute state in the form x, where:
0 = Disable (Not Muted)
1 = Enable (Muted) (default value)
2 = Unit muted due to AUX mute signal (see Note)
Note: This value is only shown in the response to a query, and cannot be given as a command. When MUT
returns a ‘2’ it indicates that one of the “hardware” mute conditions is present. For example, an auxiliary mute
could be present if the auxiliary mute has been enabled, and the signal to unmute the unit is not provided.
Additionally, certain faults can generate a hardware mute such as the BUC lock detect, the LNB current draw (if
enabled by the user), or the LNB voltage (if enabled by the user). If MUT returns an unexpected value of ‘2’
then check the active faults and the status of the auxiliary mute.
Example: <1/MUT=1’cr’
>0001/MUT=1’cr’’lf’
MUT=
MUT?
MUT*
MUT?
MUT=x
(See Description of
Arguments)
Number of Unread
Stored Events
N/A
3 bytes
Query only.
Returns the number, in the form xxx, of unread stored events
Example: <1/NUE?’cr’
>0001/NUE=126’cr’’lf’
NUE=
NUE?
NUE=xxx
Number of Unread
Stored Statistics
N/A
3 bytes
Query only.
Returns the number, in the form xxx, of unread stored statistics
Example: NUS=126
NUS=
NUS?
NUS=xxx
- Revision 10 1
- Part Number MN-LPOD 3
- Revision 10 3
- TABLE OF CONTENTS 5
- vii 9
- FIGURES 10
- PREFACE 13
- Electrical Safety Notice 14
- Product Support 15
- Preface Revision 10 16
- Chapter 1. INTRODUCTION 19
- 1.2 Functional Description 20
- 1.3 Features 20
- 1.3.7 Optional LNB Support 21
- 1.4 Theory of Operation 22
- 1.4.1 SSPA Block Diagrams 22
- 1.4.2 SSPA Module 23
- 1.4.3 Cooling System 24
- 1.4.5 LNB Operation 24
- 1.4.6 Power Supply 24
- BUC C, Ku, X LO Frequencies 25
- 1.5.1 Characteristics 26
- 1.5.4 Environmental 28
- 1.5.5 Physical 28
- 1.6 Dimensional Envelopes 30
- Introduction Revision 10 31
- Chapter 2. SYSTEM 41
- CONNECTIONS, INSTALLATION 41
- STARTUP 41
- 2.3 Interface Connectors 44
- Control Port) 48
- 2.3.8 Ground Connector 49
- 2.5 Power-up the LPOD 50
- Chapter 3. UPDATING FIRMWARE 55
- Chapter 4. ETHERNET-BASED 65
- REMOTE PRODUCT 65
- 4.3 SNMP Interface 66
- 4.3.3 SNMP Traps 67
- 4.4 Telnet Interface 70
- Enter the LPOD’s 71
- 4.5.2 User Login 73
- 4.5.3.1 Menu Tree 74
- 4.5.3.2 Page Navigation 74
- 4.5.3.3 Page Sections 74
- 4.5.3.4 Action Buttons 75
- 4.5.3.5 Drop-down Lists 75
- 4.5.3.6 Text or Data Entry 75
- 4.5.4.1 Home Pages 76
- 4.5.4.1.1 Home 76
- 4.5.4.1.2 Home 77
- 4.5.4.1.3 Home 78
- 4.5.4.2 Admin Pages 79
- 4.5.4.2.1 Admin 79
- Webpage Timeout 80
- 4.5.4.2.2 Admin 81
- 4.5.4.3 Config Pages 82
- 4.5.4.3.2 Config 84
- 4.5.4.3.3 Config 85
- Redundancy 87
- Online Status 87
- Force Online 87
- 4.5.4.4 Status Pages 88
- 4.5.4.4.1 Status 88
- 4.5.4.4.2 Status 89
- 4.5.4.4.3 Status 90
- 4.5.4.4.4 Status 91
- Alarm Mask 92
- Statistics Configuration 94
- 4.5.4.4.6 Status 95
- Control Bar and Refresh Tab 96
- Temperature Graph 97
- Power Graph 97
- LNB Current Graph 98
- Amplifier Status Graph 98
- Mute State Graph 98
- Online Status Graph 99
- Minimum Fan Speed Graph 99
- MANAGEMENT 101
- 5.2.2 Attenuator Control 102
- 5.2.3 Mute Control 102
- 5.2.4 Faults 102
- 5.2.5 Power Detector 104
- 5.2.6 Some Common Commands 104
- 5.2.7 End-of-Life Commands 104
- 5.1.1 EIA-485 105
- 5.1.2 EIA-232 106
- 5.1.3 Basic Protocol 106
- 5.1.4 Packet Structure 106
- 5.1.4.1 Start of Packet 107
- 5.1.4.2 Target Address 107
- 5.1.4.3 Address Delimiter 107
- 5.1.4.4 Instruction Code 108
- 5.1.4.7 End of Packet 109
- Appendix A. 1:1 REDUNDANCY 137
- Appendix A Revision 10 138
- A.5.1 Common Kit Examples 146
- BLANK PAGE 151
- Appendix B. CABLE DRAWINGS 193
- B.2 Control and Data Cables 194
- Appendix B Revision 10 195
- B.3 RF Cables 202
- B.3.1 RF Cable (Type ‘N’) 203
- Appendix C. MAINTENANCE 205
- Appendix C Revision 10 206
- 212
- 480 • 333 • 2200 PHONE 218
- • 333 • 2161 FAX 218
Relacionado con productos y manuales para Amplificadores de audio Comtech EF Data LPOD
(60 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales