Comtech EF Data CSAT-5060 Especificaciones Pagina 196
- Pagina / 224
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CSAT-5060 C-Band Transceiver Revision 1
Updating Firmware MN/CSAT5060.IOM
3–4
• Via Telnet Remote Control – Type the “<1/FRW?” remote query (without quotes)
at the command prompt. The unit will return the Bulk, MnC, and FPGA firmware
load information.
4. Use Telnet Remote Control to select the boot image. To select the desired boot Image, type the
“<1/IMG=1” or “<1/IMG=2” remote command (without quotes) at the command prompt..
5. Reboot the CSAT.
A. Disconnect the power source from the CSAT.
B. Re-energize the CSAT. The unit will reboot using the updated firmware image.
6. To update the other firmware image, repeat steps 1 through 5.
The CSAT is now operating with its latest firmware. The Ethernet-based firmware update process is
now complete.
- CSAT-5060 1
- Table of Contents 5
- Figures 10
- PREFACE 13
- About this Manual 14
- Conventions and References 14
- Cautions and Warnings 14
- Trademarks 14
- Safety Compliance 15
- EN 60950 15
- Low Voltage Directive (LVD) 15
- Safety Notice 15
- Preface Revision 1 16
- Warranty Policy 17
- Limitations of Warranty 17
- Exclusive Remedies 18
- Chapter 1. INTRODUCTION 19
- 1.2 THEORY OF OPERATION 21
- 1.3 RF SIGNAL CONVERSION 22
- 1.3.2 UPCONVERTER 23
- 1.4 MONITOR & CONTROL 24
- Chapter 2. SPECIFICATIONS 25
- 2.2 SPECIFICATIONS 31
- Chapter 3. CONNECTOR PINOUTS 33
- Chapter 4. SYSTEM OPERATION 35
- 4.2.2 Attenuation 36
- 4.2.3 Gain Offset 36
- 4.2.4 Mute Mode 36
- Tx Amplifier 37
- 4.2.8 Channel Slope Adjust 38
- Cold Start Function 39
- Auto Fault Recovery 39
- LNA Current Source 40
- LNA Fault Logic 40
- 4.2.18 Set Physical Address 41
- Set Time 42
- Set Baud Rate 42
- Set Date 42
- Chapter 5. REDUNDANT SYSTEMS 43
- 5.1.1 RSU-5060 INTERFACES 44
- Electrical Interface 44
- CSAT Unit A Interface, J1 44
- CSAT Unit B Interface, J3 45
- M&C Interface, J5 46
- Rx IF Interfaces, J9 – J11 47
- Mechanical Interface 47
- RSU-5060 Operation 48
- RS-485 Interface 49
- RED AUTO/MANUAL Signal 49
- SWITCH CMD Signal 50
- REDUNDANCY A/B Signals 50
- REDUND_FLT Signal 50
- AUXCOM Signals 50
- Chapter 6. REMOTE CONTROL 53
- Basic Protocol 54
- Packet Structure 55
- Start Of Packet 55
- Commands or Responses 58
- UGO= 5 bytes 59
- DGO= 5 bytes 59
- Chapter 7. MAINTENANCE AND 73
- TROUBLESHOOTING 73
- 7.1 Maintenance Testing 74
- 7.2 Troubleshooting 74
- 7.3 Converter Faults 74
- DC Power Supply Voltages 74
- 7.3.2 RF Converter Module 75
- 7.3.4 LNA Curent Fault 75
- 7.3.5 Fan Fault 76
- 7.3.6 Temperature Fault 76
- Chapter 8. LNA INSTALLATION 77
- - Not shown 78
- NSTALLATION OF LNA ASSEMBLY 82
- Redundant LNA Assembly 83
- Chapter 9. CSAT-5060 85
- +10 dBm Unit 85
- 9.1.1 Function Description 86
- 9.1.2 Prime Power Level 86
- 9.1.3 Physical Dimensions 86
- 9.2 9.2 Specifications 87
- A.2.1 Mounting Kit 92
- Hardware 97
- A.2.3 Cable Installation 98
- A.3 SPAR-MOUNT INSTALLATION 99
- IMPORTANT 101
- A.3.3 Cable Installation 102
- TX Switch 105
- Transceivers 111
- Configuration 111
- A.5.1 Cable Installation 112
- (Block Diagram) 113
- Mounting Kits 116
- B.4.2 S 119
- -THREAD INSTALLATION 119
- B.4.3 Cable Installation 123
- . Cable Kit 126
- Redundancy Installation 130
- Figure B-17. Pipe Blocks 133
- Blocks 133
- Cable Installation 136
- C.3 Tools Required 140
- C.4.1 Mounting Kits 140
- Looking down 143
- 145
- EDUNDANCY CONFIGURATION 147
- Step Procedures 154
- Switch, AS/0478 154
- C.6 CABLE INSTALLATION 158
- C/S = CUSTOMER - SUPPLIED 159
- Addendum A 161
- BLANK PAGE 162
- Addendum A. ETHERNET 165
- BASED REMOTE PRODUCT 165
- MANAGEMENT 165
- AA.3 SNMP Interface 166
- AA.3.3 SNMP Traps 167
- AA.4 Telnet Interface 168
- AA.5.2 User Login 172
- AA.5.3.5 Text or Data Entry 175
- AA.5.5.1 Home Pages 176
- AA.5.5.1.1 Home 176
- Contact Information 178
- Problem Report 178
- AA.5.5.2 Admin Pages 179
- Webpage Timeout 180
- AA.5.5.3 Config Pages 183
- Reference Adjust 184
- AA.5.5.3.2 Config 185
- AA.5.5.3.3 Config 186
- Date and Time 187
- Circuit ID 187
- AA.5.5.4 Status Pages 190
- Unread Stored Alarms: ## 191
- Chapter 3. UPDATING FIRMWARE 193
- Appendix A. REMOTE CONTROL 197
- A.1.2 EIA-232 198
- A.2 Basic Protocol 198
- A.3 Packet Structure 199
- A.3.1 Start Of Packet 199
- IMPORTA N T 200
- A.3.7 End Of Packet 203
- A.4.2 CSAT Remote Commands 205
- UGO= 5 bytes 206
- DGO= 5 bytes 206
- – same as UGO= (5 bytes) 209
- 480 • 333 • 2200 PHONE 224
- 480 • 333 • 2161 224
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales