Comtech EF Data Vipersat CDM-570 Guía de usuario Pagina 36
- Pagina / 162
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Initial Configuration
2-12 Vipersat CDM-570/570L User Guide
7. Enter I at the command prompt to set the Managing IP Address.
The Managing IP Address is the IP address of the VMS server.
8. Enter H to go to the Home State Configuration menu screen, then enter
W to set the current configuration as the Home State.
9. Save the settings to flash by entering S at the command prompt.
This completes the initial configuration of a CDM-570/570L from the factory
default settings to a functioning, Vipersat-enabled unit. Additional configura-
tion parameters must be set depending on the network requirements for a
specific application.
Refer to Chapter 3, “Using the Command Line Interface,” for additional details
on configuring the target Vipersat CDM-570/570L.
- User Guide 1
- Vipersat CDM-570/570L 3
- Version 1.5.x 3
- COMTECH EF DATA 4
- Document Revision Status 5
- Table of Contents 7
- Network Addressing 8
- Automatic Switching 9
- Dynamic Power Control 9
- Network Migration 9
- Glossary 9
- L User Guide 10
- List of Figures 11
- Appendix A Figures 12
- Appendix B Figures 12
- Appendix C Figures 12
- Appendix D Figures 12
- List of Tables 13
- How to Use This Manual 15
- Conventions and References 16
- Chapter 1 - General 1-3 17
- Product Description 18
- Dynamic SCPC (dSCPC) 19
- New in this Release 20
- 1.5.4 Release 21
- Customer Support 23
- QUICK START CONFIGURATION 25
- Initial Configuration 26
- Network Role 27
- Parameters 27
- Figure 2-3 29
- Figure 2-4 29
- Set the IP Address 30
- Configure the Route Table 31
- Figure 2-8 34
- Common Screen Commands 38
- Menu Descriptions 39
- Feature Configuration 41
- Vipersat Management 42
- Vipersat STDMA 42
- Vipersat Auto Switching 42
- Vipersat File Streamer 43
- Vipersat Configuration 44
- STDMA Tx Rate 45
- Hub Type 46
- Group ID 48
- STDMA Power Hunt 49
- Burstmap Multicast IP 50
- Outbound IP 50
- Cycles Per Burst Map 51
- Slot Guardband 51
- Slot Preamble Length 52
- Slot Data Length 52
- Slot Cycle Length 53
- Slot Start in Cycle 53
- Set Remotes 53
- STDMA Statistics 60
- Show Hub Statistics 61
- Figure 3-34 63
- Auto Switching 64
- Current WAN Transmit Mode 64
- ToS Switch Detection 66
- QoS Switch Detection 67
- STDMA Slot Capacity 70
- STDMA Switch Delay 70
- Percent Allocation 71
- SCPC Step Up Threshold 71
- SCPC Step Down Threshold 72
- SCPC Step Delay 72
- SCPC Step Up Excess 73
- ToS Switching Parameters 74
- Time for Carrier Inhibit 74
- Hitless Switching Parameters 77
- SOTM Update 78
- Unit Role 79
- Expansion Unit 80
- Network ID 80
- Unit Name 81
- Receive Multicast Address 81
- Managing IP Address 82
- Primary Heart Beat 83
- Home State Revert 83
- DPC Enabled 85
- Calibrated Data Rate 85
- Nominal Power Level 86
- Max Power 86
- Min Power 86
- Target EbNo 87
- Target Range 87
- Speed Up EbNo 87
- Target DPC Address 88
- Set Home State Parameters 89
- Force Modem to Home State 91
- STDMA State 91
- Transmit Frequency 91
- Transmit Data Rate 91
- Transmit FEC Type 92
- Transmit Coding Rate 92
- Transmit Modulation Type 93
- Transmit Power Level 93
- Transmit Enable 93
- Receive Frequency 93
- Receive Data Rate 94
- Receive FEC Type 94
- Vipersat Summary 95
- Vipersat Migration 97
- UDP Port Base Address 97
- NETWORK ADDRESSING 99
- The OSI Reference Model 100
- Binary Math 102
- IP Addressing 104
- Private Network IP Addresses 106
- Subnet Mask 107
- Network Segments 108
- Example: 00-3f-bf-00-01-45 109
- AUTOMATIC SWITCHING 111
- Load Switching 113
- Load Switching Process 116
- Load Switching by a Remote 117
- Load Switch Example 118
- Application Switching 121
- B - Automatic Switching B-13 123
- Fail-Safe Operation 124
- Figure B-5 125
- Figure B-6 126
- DYNAMIC POWER CONTROL 127
- Description 129
- Adjustment for Data Rate 131
- DPC Scaling Function 132
- NETWORK MIGRATION 135
- Firmware Upgrade 137
- Migration Procedure 138
- Upgrade Router to v1.5.3 141
- Save and Reboot to Latest 143
- Completing Migration 150
- Remote units 151
- GLOSSARY 153
- Appendix E - Glossary E-3 155
- Appendix E - Glossary E-5 157
- Appendix E - Glossary E-7 159
- Appendix E - Glossary E-9 161
Relacionado con productos y manuales para Redes Comtech EF Data Vipersat CDM-570
Redes Comtech EF Data SDM-100A Manual de usuario
(4 paginas)
(4 paginas)
Redes Comtech EF Data Vipersat SLM-5650A Guía de usuario
(320 paginas)
(320 paginas)
Redes Comtech EF Data CDM-710G Especificaciones
(238 paginas)
(238 paginas)
Redes Comtech EF Data Vipersat CDD-564L Especificaciones
(172 paginas)
(172 paginas)
Redes Comtech EF Data CDM-800 Manual de usuario
(41 paginas)
(41 paginas)
Redes Comtech EF Data CDM-710L Especificaciones
(252 paginas)
(252 paginas)
Redes Comtech EF Data CDD-880 Especificaciones
(92 paginas)
(92 paginas)
Redes Comtech EF Data CDM-600 Manual de usuario
(2 paginas)
(2 paginas)
Redes Comtech EF Data CDM-600 Especificaciones
(90 paginas)
(90 paginas)
Redes Comtech EF Data CDM-600 Manual de usuario
(4 paginas)
(4 paginas)
Redes Comtech EF Data CDM-Qx Manual de usuario
(4 paginas)
(4 paginas)
Redes Comtech EF Data CDM-600 Manual de usuario
(4 paginas)
(4 paginas)
Redes Comtech EF Data CDM-840 Especificaciones
(110 paginas)
(110 paginas)
Redes Comtech EF Data CDM-625 Manual de usuario
(5 paginas)
(5 paginas)
Redes Comtech EF Data CDM-Qx Manual de usuario
(4 paginas)
(4 paginas)
Redes Comtech EF Data CDM-500 Especificaciones
(88 paginas)
(88 paginas)
Redes Comtech EF Data Vipersat 564L Guía de usuario
(176 paginas)
(176 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales