Comtech EF Data SDM-100A Especificaciones Pagina 112
- Pagina / 212
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Operation SDM-100A Satellite Modem
3–78 Rev. 0
TR
A
NSMIT RF
EQUIPMENT
CUSTOMER
D
A
T
A
INTERF
A
CE
ENCODER
/
MODUL
A
TOR
A
NTENN
A
A
CPOWER
POWER
SUPPLY
MICRO-
COMPUTER
REMOTE
SERI
A
L
INTERF
A
CE
F
A
ULT
INDIC
A
TORS
RECEIVE RF
EQUIPMENT
DEMODUL
A
TOR
/
DECODER
S
A
TELLITE
SDM-100A
D
A
T
A
MODEM
Figure 3-27. IF Loopback
Note: When IF loopback is turned on, the demodulator is looped back to the modulator inside the modem, and the
demodulator is programmed to the same frequency as the modulator. This test mode will verify the operation of the
modem. When IF loopback is turned off, the demodulator is programmed back to its previous frequency, and is
reconnected to the IF input.
TR
A
NSMIT RF
EQUIPMENT
CUSTOMER
D
A
T
A
INTERF
A
CE
ENCODER
/
MODUL
A
TOR
A
NTENN
A
A
CPOWER
POWER
SUPPLY
MICRO-
COMPUTER
REMOTE
SERI
A
L
INTERF
A
CE
F
A
ULT
INDIC
A
TORS
RECEIVE RF
EQUIPMENT
DEMODUL
A
TOR
/
DECODER
S
A
TELLITE
SDM-100
A
D
A
T
A
MODEM
Figure 3-28. Baseband Loopback
Note: When baseband loopback is turned on, the data signal is looped back on the customer side of the interface.
This test mode will verify customer equipment, as well as cabling between the modem and the customer equipment.
- SDM-100A 1
- Preface 5
- Military Standards 6
- Trademarks 6
- Related Documents 6
- European EMC Directive 7
- Customer Support 8
- Table of Contents 9
- Rev. 0 vii 11
- Rev. 0 ix 13
- Figures 14
- Rev. 0 xi 15
- Chapter 1 17
- INTRODUCTION 17
- 1.1 Purpose and Function 18
- 1.2 Description 19
- 1.3 Options 20
- 1.3.1 ASYNC/AUPC Interface 20
- 1.3.2 ADPCM Voice 20
- 1.4 Modem Specifications 21
- 1.5 BER Performance 23
- 1–8 Rev. 0 24
- Rev. 0 1–9 25
- 1–10 Rev. 0 26
- Chapter 2 27
- INSTALLATION 27
- 2.2 System Installation 28
- 2.3 System Requirements 29
- 2–4 Rev. 0 30
- 2.4 External Connections 31
- 2.4.2 Remote (J6) 32
- 2.4.3 Faults (J7) 33
- 2.4.4 TX IF Output (CP1) 33
- 2.4.5 RX IF Input (CP2) 34
- 2.4.6 AC Power 34
- 2.4.7 DC Power 34
- 2.4.8 GND 34
- 2.4.9 AGC Test Point 34
- Chapter 3 35
- OPERATION 35
- 3.1.2 LED Indicators 36
- 3.1.3 Front Panel Controls 37
- 3.2 Menu System 38
- Rev. 0 3–5 39
- 3–6 Rev. 0 40
- 3.2.1.1 Configuration 41
- 3–8 Rev. 0 42
- Rev. 0 3–11 45
- 3–12 Rev. 0 46
- Rev. 0 3–15 49
- 3–16 Rev. 0 50
- Rev. 0 3–17 51
- Rev. 0 3–21 55
- 3–22 Rev. 0 56
- 3–24 Rev. 0 58
- 3.2.1.2 Monitor 59
- 3.2.1.3 Faults/Alarms 60
- Rev. 0 3–27 61
- 3–28 Rev. 0 62
- 3.2.1.3.1 Modulator Faults 63
- Rev. 0 3–33 67
- 3–34 Rev. 0 68
- Rev. 0 3–35 69
- 3.2.1.5 Remote AUPC 70
- 3.2.1.6 Utility 71
- 3–38 Rev. 0 72
- 3.2.1.6.1 Utility Modulator 73
- Rev. 0 3–41 75
- 3–42 Rev. 0 76
- 3–44 Rev. 0 78
- 3.2.1.6.3 Utility Interface 79
- Rev. 0 3–47 81
- 3–48 Rev. 0 82
- 3.2.1.6.4 Utility System 83
- again to reset the 84
- Rev. 0 3–51 85
- 3–52 Rev. 0 86
- Rev. 0 3–53 87
- 3–54 Rev. 0 88
- ↑] or [↓] to increase or 91
- ←] and [→] to move the 93
- Rev. 0 3–61 95
- 3–62 Rev. 0 96
- 3–64 Rev. 0 98
- Rev. 0 3–65 99
- 3.2.2.5 Utility Functions 100
- Rev. 0 3–67 101
- 3–68 Rev. 0 102
- 3–70 Rev. 0 104
- 3–72 Rev. 0 106
- ↑] or [↓] to 107
- ↑] or [↓] to select ON 107
- SATELLITE 111
- DATA MODEM 111
- 3.3 Clocking Options 113
- 3.3.1 Master/Master 113
- 3.3.2 Master/Slave 113
- 3–80 Rev. 0 114
- Rev. 0 3–81 115
- 3–82 Rev. 0 116
- Chapter 4 117
- THEORY OF OPERATION 117
- ± 1 x 10 119
- ± 1 dB to 119
- STANDARD 120
- NON-STANDARD 120
- 4.1.2 Specifications 121
- 4.2 Demodulator 122
- 4.2.1 Theory of Operation 122
- 4.2.2 Specifications 122
- RX CLOCK 123
- 4–8 Rev. 0 124
- Rev. 0 4–9 125
- 4–10 Rev. 0 126
- 4.3 Monitor and Control 127
- 4.3.1 Non-Volatile Memory 127
- 4–12 Rev. 0 128
- 4.3.5 Modem Defaults 129
- 4.4 Digital Interfaces 130
- 4.4.1 RS-422 Interface 130
- 4–16 Rev. 0 132
- 4.4.1.1 Connector Pinouts 133
- 0.0, ± 0.4V 134
- Rev. 0 4–19 135
- 4–20 Rev. 0 136
- 4.4.2.1 Connector Pinouts 137
- 4.4.2.2 Specification 138
- 4.4.3 RS-232-C Interface 138
- 4.4.3.1 Theory of Operation 139
- 4–24 Rev. 0 140
- 4.4.3.2 Connector Pinouts 141
- Chapter 5 143
- MAINTENANCE 143
- 5.1.2 Modulator Checkout 144
- 5.1.3 Demodulator Checkout 144
- Rev. 0 5–3 145
- Various Code Rates 146
- WITH NOISE 147
- WITHOUT NOISE 147
- 5.1.4 Test Points 148
- INTERFACE FAULTS 150
- MOD FAULTS 150
- DEMOD FAULTS 150
- COMMON EQUIPMENT FAULTS 150
- 5.3 Module Identification 151
- 5–10 Rev. 0 152
- Appendix A 153
- REMOTE CONTROL OPERATION 153
- A.2 Message Structure 154
- A.2.1 Start Character 154
- A.2.2 Device Address 154
- A.2.3 Command/Response 155
- A.2.4 End Character 155
- Command: 156
- (MPO_) 157
- A.3.2 Demodulator 158
- Rev. 0 A–7 159
- A.3.3 Interface 160
- Rev. 0 A–9 161
- A–10 Rev. 0 162
- Rev. 0 A–11 163
- A.3.4 System 164
- A.3.5 AUPC 164
- Rev. 0 A–13 165
- Modulator Output Power 166
- A–16 Rev. 0 168
- Rev. 0 A–17 169
- A–18 Rev. 0 170
- Rev. 0 A–19 171
- A–20 Rev. 0 172
- Rev. 0 A–21 173
- A–22 Rev. 0 174
- Rev. 0 A–23 175
- A–24 Rev. 0 176
- Rev. 0 A–25 177
- A–26 Rev. 0 178
- A.4.2 Error Performance 179
- A.5 Stored Faults 180
- Rev. 0 A–29 181
- A–30 Rev. 0 182
- Appendix B 183
- OPTIONS 183
- B–2 Rev. 0 184
- B.1.1 Theory of Operation 186
- B.1.1.5 Buffer Operation 187
- B.1.1.8 Non-ASYNC Operation 188
- B.1.2.1 Top Cover Removal 190
- B.1.2.3 EPROM Installation 190
- B.1.2.4 ASYNC Interface 190
- B.1.3 Front Panel Operation 191
- B.1.3.3 Demodulation 192
- B.1.3.4 Utility/Interface 192
- B.1.3.5 Specifications 193
- Rev. 0 B–13 195
- B.2.1.1 Multiplexer 196
- B.2.1.2 Demultiplexer 196
- B.2.1.3 Protection Switch 197
- B.2.1.4 RS-422 Interface 197
- B.2.2 Front Panel Operation 198
- B.2.2.1 Interface 198
- B.2.2.4 Utility/Interface 199
- B.2.2.5 TX Alarm Indication 199
- B.2.2.6 RX Alarm Indication 199
- B.2.2.7 DEMUX Lock 199
- B.2.2.8 Remote Off Hook 199
- B.2.3 Specifications 200
- B.3 Reed-Solomon Codec 201
- B.3.1 Reed-Solomon Encoder 201
- B–20 Rev. 0 202
- Rev. 0 B–21 203
- B.3.2 Reed-Solomon Decoder 204
- Rev. 0 B–23 205
- B–24 Rev. 0 206
- Glossary 207
- METRIC CONVERSIONS 211
- Units of Length 211
- Temperature Conversions 211
- Units of Weight 211
- 480 • 333 • 2200 PHONE 212
- 480 • 333 • 2161 212
Relacionado con productos y manuales para Redes Comtech EF Data SDM-100A
Redes Comtech EF Data Vipersat CDM-570 Guía de usuario
(192 paginas)
(192 paginas)
Redes Comtech EF Data CDM-Qx Especificaciones
(258 paginas)
(258 paginas)
Redes Comtech EF Data CDM-Qx Especificaciones
(260 paginas)
(260 paginas)
Redes Comtech EF Data CDM-500 Manual de usuario
(5 paginas)
(5 paginas)
Redes Comtech EF Data CDM-500 Manual de usuario
(4 paginas)
(4 paginas)
Redes Comtech EF Data CDM-700 Especificaciones
(266 paginas)
(266 paginas)
Redes Comtech EF Data CDD-880 Manual de usuario
(34 paginas)
(34 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.098 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales