Comtech-ef-data M&C Software for Windows Manual de usuario

Part Number MN/M-CWIN.IOM Revision 4 IMPORTANT NOTE: The information contained in this document supersedes all previously publishe

M&C Software for Windows Revision 4 Preface MN/M-CWIN.IOM viii Notes:

1–1 Chapter 1. GETTING STARTED The Comtech EF Data Monitor and Control (M&C) software is a Windows-based program designed to provide a user-fri

Monitor and Control Software for Windows Revision 4 Getting Started MN/M-CWIN.IOM 1–2 1.2 Installation IMPORTANT 1. Delete any existing M&C

Monitor and Control Software for Windows Revision 4 Getting Started MN/M-CWIN.IOM 1–3 Screen Description Pre-Select Screen The Pre-Select Scree

Monitor and Control Software for Windows Revision 4 Getting Started MN/M-CWIN.IOM 1–4 Current Fault Log Screen The RF terminals connected to this

Monitor and Control Software for Windows Revision 4 Getting Started MN/M-CWIN.IOM 1–5 1.5 Navigation The active screen is displayed on the lower

Monitor and Control Software for Windows Revision 4 Getting Started MN/M-CWIN.IOM 1–6 1.6 Equipment Line Communications are continually verified

2–1 Chapter 2. OPERATION This chapter provides information regarding the operation of the M&C software. 2.1 Supported Terminals The initial r

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–2 2.2 Startup To start the application, double-click the M&C ico

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–3 2.1.1.1 Communications Dialog Box The communications dialog box

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–4 2.1.1.2 Command Delay Dialog Box The application performs backgrou

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–5 2.1.1.3 Configuration Dialog Box The configuration dialog box (Fi

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–6 2.1.1.4 Terminal Macros Dialog Box The third choice under the Opti

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–7 2.3 The Menu Bar The menu bar contains four different menus: Fil

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–8 • The Clear Selected Faults is selectable only when the active scr

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–9 2.4 Screen Details The application uses five primary screens. Ea

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–10 2.4.1 Status Screen The Status Screen (Figure 2-10) reports fault

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–11 CANCEL and SEND buttons, the highlighted yellow fields are chang

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–12 Figure 2-11. Pre-Select Screen

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–13 2.4.3 Comm/Util Screen The Comm/Util Screen (Figure 2-12) repor

Copyright © 2010 Comtech EF Data. All rights reserved. Printed in the USA. Comtech EF Data, 2114 West 7th Street, Tempe, Arizona 85281 USA, 480.333.22

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–14 The ACQUIRE COMMUNICATIONS button loads the Acquire Communications

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–15 2.4.4 Terminal Screen The terminal screen (Figure 2-14) allows

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–16 The communication setup frame shows communication parameters as se

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–17 2.4.5 Fault Log Screen The fault log screen (Figure 2-15) shows

Monitor and Control Software for Windows Revision 4 Operation MN/M-CWIN.IOM 2–18 This page is intentionally left blank.

3–1 Chapter 3. TROUBLESHOOTING This chapter describes troubleshooting possible problems and methods for solving them. 3.1 EIA-232 to EIA-485 Conver

Monitor and Control Software for Windows Revision 4 Troubleshooting MN/M-CWIN.IOM 3–2 CAUTION Some EIA-232 to EIA-485 converters electrically conne

Monitor and Control Software for Windows Revision 4 Troubleshooting MN/M-CWIN.IOM 3–3 3.3 Communication with Redundant Systems All non-KST-2000A/B

Monitor and Control Software for Windows Revision 4 Troubleshooting MN/M-CWIN.IOM 3–4 All KST-2000A/B redundant systems serviced by the application

METRIC CONVERSIONS Units of Length Unit Centimeter Inch Foot Yard Mile Meter Kilometer Millimeter 1 centimeter — 0.3937 0.03281

This page is intentionally blank.

2114 WEST 7TH STREET TEMPE ARIZONA 85281 USA 480 • 333 • 2200 PHONE 480 • 333 • 2161 FAX

iii Table of Contents TABLE OF CONTENTS ...

M&C Software for Windows Revision 4 Table of Contents MN/M-CWIN.IOM iv 2.3 The Menu Bar ...

v PREFACE About this Manual This manual describes the Comtech EF Data WindowsTM based Monitor and Control (M&C) software used with Comtech EF Data

M&C Software for Windows Revision 4 Preface MN/M-CWIN.IOM vi Cautions and Warnings IMPORTANT IMPORTANT or NOTE indicates a statement associate

M&C Software for Windows Revision 4 Preface MN/M-CWIN.IOM vii Customer Support Contact the Comtech EF Data Customer Support Department for: